The echosounder

Most carp anglers possess an echosounder.
Just like a rod and a boilie the echosounder has become an aid to put fish on the bank.

Especially on large waters the echosounder makes finding features and interesting spots such as
a plateau much easier.

Location of the fish is the key to successful angling.
At the beginning of a session one should never just cast out „blind“; it is very important to find the fish first or at least some spots where the fish are likely to feed.
Here the echosounder can be a big help.

Let´s now take a closer look at the echosounder and its functions.
An echosounder which is of interest for the carp angler is a small portable waterproof unit with
a liquid crystal screen, a battery  pack and a transducer which is linked to the screen by a cable.

An echosounder works on the basis of sonar technology.
The transducer is mounted to your boat. In the water the transducer sends out a signal 10 – 12 times per second. These signals are reflected by the bottom and then return to the transducer which picks up the returning signals.
The speed of the signals travelling through the water are pre-programmed in the echosounder, hence the sounder is able to calculate the depth and the bottom profile which is then indicated on the screen of the sounder.
Fish can also be seen on the screen because they return their own signal to the transducer before the signals sent out by the transducer reach the bottom.

It´s important to fit the transducer in the right way, hence always read the instructions in your sounder manual carefully.
If the transducer isn´t mounted in the right way you´ll get wrong information on your screen.

The size of the area the transducer covers is determined by the frequency and the cone angle of the signals which the transducer sends out .
When the signals hit the bottom the area covered is like a circular footprint of the water bottom.
Just like a torch shining on the bottom.
With a standard transducer on echosounders sold by Eagle and Lowrance the cone angle is 20°  and the diameter of the circular footprint on the bottom of the water is about a third of the measured depth.

This might sound very little to some. Let´s again take the torch as comparison.
A torch with a fairly wide light beam will illuminate a fairly large area. But such a torch will not go as far as a torch with a narrow light beam would go.

That´s why it is important to get the combination right.
A cone of 20° and a frequency of 192 kHz (amount of signals per second) is the right combination between covered surface and detailed information for depths ranging from
0 – 120 meters.

The frequency of the transducer also determines the performance of your sounder.
The higher the frequency the better will be the resolution on your screen , but high frequencies don´t travel through water as easily as low frequencies do. Then again too low frequencies won´t give much information on the screen of your sounder.

For freshwater use a transducer with a cone angle of  20° and a frequency of 192 kHz offers the best combination between  covered area and detailed information on your screen.

Nobody fishes for carp deeper than 50 meters so there´s no need to worry that the signals sent out by the transducer won´t reach the bottom of the water.

An echosounder is by no means an under water camera with which the angler can see which kind of fish is swimming below his boat and how big it is. But if the echosounder is used in the right way it can give the angler a lot of important information about a water.
To know the bottom profile of a water ( weed , snags,  hard or soft bottom, etc.) can be very useful for catching carp.

With the aid of an echosounder one can find  plateaux, holes in the bottom, slopes and snags like sunken trees and of course determine the depth.

Once you´ve found an interesting spot you can drop a marker on the spot and then row around the marker to further investigate the area you´ve chosen  to see if there are snags, etc. .

Most echosounders sold by Eagle and Lowrance have a Grayline function .
With the aid of this function you can check how hard the bottom is.
If there´s a lot of grey in the area below the black bottom line on your screen the bottom is hard.
If the bottom is soft or covered with weed you´ll get very little or no Grayline indication on your screen.
Hard bottom reflects the signals sent out by the transducer better than soft bottom does.

As an example : a tennis ball which you throw against a wall will fly back towards you,
whilst a ball thrown against a curtain will not come back
(unless there´s a wall behind the curtain).
Hence with echosounders that have the Grayline function you´ll be able to see if the bottom
is hard or soft.

If there´s weed on the bottom ( sometimes it reaches right to the surface) your echosounder will only indicate a thin layer of Grayline below the black bottom line on your screen.
The weed is shown by means of  black lines reaching towards the surface, depending on how thick the weed is.

As you can see the Grayline function will be able to give you valuable information for your hookbait presentation. If the bottom is covered by a thin layer of weed it might be worth fishing a pop up sitting nicely on top of the weed.
A bait presented in that way will be found more easily by the carp.

A spot with a hard bottom on a water that has a soft / muddy bottom in most parts can also be
a hot spot.
With the aid of the Grayline function one can find these spots.


Carp usually reflect the signals sent out by the transducer quite well and thus the fish will be shown on the screen of your sounder.

Carp tend to swim fairly slowly and also they have a large back and a big swim bladder.
All this aids a good reflection of the signal to the transducer.

Fish with large swim bladders reflect the signals very well because the signals which the transducer sends out can´t go through the air inside the swim bladder, hence they are reflected and return to the transducer.

You can never be  100 % sure that it´s a carp below your boat but if you see one or more fish swimming near the bottom on your screen but chances are high that you´ve found some carp.
Pike and Zander don´t swim in shoals.
A shoal of roach is indicated by a black cloud on your screen.

If one switches on the fish ID function you get fish symbols in three to four sizes on your screen.
If there´s for example a shoal of roach swimming below your boat the sounder will show you one or two fish symbols on the screen if the fish ID function is switched on.

Once you´ve located fish it is better to switch off the fish ID function and check in the normal mode if there´s just many small fish below your boat or one big fish.

Single small fish give a very weak signal on the screen .
In the standard mode with the fish ID function switched off  big fish are indicated as bows on the screen.  The bigger the bow the bigger the fish.

If there´s a carp of more than 10 kg below your boat you usually get a bit of Grayline in the bow on the screen.
Always keep in mind that in shallower water a small fish gives a stronger signal than it would in deeper water.

On the Eagle Ultra Classic and the Lowrance X – 65 there´s also a split screen function.
This function as the name says allows you to split the screen. In one half of the screen you can then observe the bottom in the normal resolution whilst on the other half you can use the 2 times or 4 times zoom which gives you even more information about a particular spot.

This function is particularly useful for checking a swim for snags but also if you want to check
a large area of a water as you´ve always got the standard screen plus the more detailed one.

Nowadays there are a lot of different echosounders on the market and the reader will ask himself which one is best suited for the carp angler.

The most important function is the Grayline as it gives the angler a lot of information about the actual bottom profile.
A large screen of at least 100 pixels with a good resolution is a must.

A transducer of 192 kHz  /  20 °  is absolutely sufficient for exploring the largest
French reservoir.


I can recommend two models in particular : the Eagle Ultra Classic and the Lowrance X- 65 .

For a couple of years now I´ve been using the Lowrance X – 65 and in my opinion it is  the best echosounder for carp anglers currently available.
The menu is simple. Once you´ve chosen your settings the X- 65 saves these and the next time you switch on your sounder the settings are the same as the last time you`ve used it.

The X- 65 is available in different language menus (French, English, German, ...)
The screen has 160 vertical pixels offering an ideal resolution of the signals the transducer has picked up.

No matter if I´m fishing the Rhine in Germany or a large French reservoir , I always take my echosounder with me as it allows me to obtain a lot of useful information about a water in a short period of time. This in turn helps me to put more fish one the bank.

 

Christian Finkelde

powered by motion-park.com