HOW TO MAKE YOUR OWN MARKER/PIKE
FLOATS

Marker and Pike Floats made by
Chris |
It is very easy to make your own Pike/Marker Floats; it’s
also much cheaper than buying them and much more fun to make
them yourself.
I have been making my own floats for over 20 years now and
I began when I was 13 or 14 years old. I have designed my own
floats and tested them. Some work great, some not so well and
a few have been useless.
I am always looking out for new materials to use and I have
stumbled across some great materials for making floats.

Tools and
materials |
But by far the best material I have used for floats;
especially Pike/Marker Floats is Balsa Wood.
It will stand quite a good beating and it is easy to shape
when making the floats.
I have made floats from polystyrene, cork , quills (bird’s
feathers), reeds, plastic tubes, drinking straws, aluminium
and of course balsa wood.
Equipment
This is a list of equipment needed to
make a Pike/Marker float:
1. Balsa Wood
2. Paint – black, white & fluoro
orange
3. Varnish
4. Paint Brushes
5. Sharp
Knife
6. Sandpaper – course & smooth
7.
Swivels
8. Superglue
9. Pliers
10. Drill bits
11.
Ruler or tape measure
Materials to make the vein
This is a list of
equipment needed to make a vein:
1. Balsa wood 6mm x 6mm
2. Hacksaw Blade
3. A sheet
of plastic 1mm thick
4. Sharp Knife
5. Sandpaper
6. A
Pencil
7. Drill bits
8. Superglue
9. Ruler or tape
measure
10. Paint – black, white & fluoro orange
11. Varnish
How to make the float
Step 1
Cut a
length of Balsa Wood, for example 15 cm x 2.5cm x 2.5cm. (If
you can find Balsa Wood that is already round like a cigar
shape, then that’s great. I have been looking everywhere and
can only find it in square pieces measuring 100cm x 2.5cm x
2.5cm.)
Then take the sharp knife and whittle it until it becomes
round. This is easier than it sounds because the balsa is
really soft. Don’t worry about getting it perfectly round with
the knife.
Step 2
Then take a course piece of sandpaper and
sand it to the exact shape that you want the float to be.
This is also quite easy due to the softness of the wood.
Once it’s the shape you want, smooth it off with the fine
sandpaper.
Step 3
When the balsa is ready, take the swivel
& pliers and push the swivel into the bottom end of the
float until there is just one eye of the swivel sticking out
of the wood (this is the eye you would hold with the pliers).
Then pull the swivel out of the float again and fill the
hole with super glue and push the swivel back in again.
Try not to get glue in the swivel or it will prevent the
eye from rotating.
Leave the glue to dry for a few minutes.
Step 4
The float is now ready for painting but
before painting it wipe off any dust from the float.
Take the white paint and paint the top end as this is going
to be the visible end that sticks up out of the water. Once
you have painted it let it dry.
Then lightly rub it down with the smooth sandpaper removing
any rough parts.
Don’t rub too hard, as you will remove the paint as well.
Once this is done give it a quick wipe and another coat of
white paint. Then let it dry again.
Once it’s completely dry, give it another rub with the
smooth sandpaper and then wipe the dust off with a cloth.
Step 5
Once the white undercoat is dry, take your
fluorescent paint (red, orange or yellow) and paint over the
white end.
Note: You must put an undercoat of white paint on
before the fluorescent paint or the fluorescent paint will not
be fluorescent.
Once again, when it is dry sand it down and give it another
coat of paint.
Let it dry completely before the next step.
Step 6
When it’s dry, it’s time to paint the
bottom end (the end that will be submerged in the water).
You do not have to paint this end if you don’t want to;
it’s obviously your choice.
If you do paint it, it doesn’t necessarily have to be
black.
I usually paint mine black, dark brown or dark green. But I
have made some and left the wood showing through and just
varnished it (see pic at top).
Once you have given it a couple of coats let it dry
completely before the next step.
Step 7
When the paint is dry give the whole of
the float a coat of varnish and hang it up to dry. Once again
be careful not to get varnish in the swivel or it won’t
rotate.
You can always give it two coats of varnish if you wish.
You can use boat varnish, which is very tough and really
protects the paint, or an aerosol varnish from a hobby shop
will do. But if you use this, spray the float outside as the
fumes from this kind of varnish are really strong.
How to make the vein
If you are really feeling
adventurous you could add a visible flight to your Balsa
Marker float.
Not only does this increase the visibility of the float but
also assists when casting, as the float will fly straight like
an arrow. This makes the cast more accurate and increases the
casting distance.
You can use the stems and flights from a normal set of
darts and paint them yourself or you can make your own from a
piece of balsa wood for the stem and cut the flight arrows out
of a 5 litre plastic juice bottle.
Firstly, measure and draw your vein on the plastic and cut
it out using a sharp knife. When you have cut out one of the
veins, use this one as a template and draw a line round it.
Then cut your second one out of the plastic.
You should have two halves of the vein now that are both
the same size.
Now you need to cut out the two slots in the veins so they
can be fitted together in a cross shape.
To cut the slots, measure half way from the bottom of the
vein to the middle on one of them, and do the same on the
other but measure from the top to the middle.
Then carefully cut the slots out of the vein.
To make the stem of the vein, take the 6mm x 6mm piece of
balsa wood and cut a cross down the centre. This should be
slightly smaller than the length of the vein. When you have
done this you can shape the stem so it becomes round. This is
best done with just sandpaper and not a knife.
You can now cut the stem to the length you require
remembering to leave an extra 20mm so you can insert this into
the float.
To insert the stem into the float reduce the thickness of
the stem by about 1mm with a sharp knife and sandpaper. Then
drill a hole in the top of the float the same size as the
stem.
Then insert the stem and glue it in. Once you have got it
right you can glue the vein into the stem as well.
Lightly sand the plastic vein so it leaves a rough surface
for the paint to stick to.
Then when the glue is dry you can paint it as you have the
top of the float.
Chris Thornhill, http://www.screamingdelkims.se/.