How to spod
Spodding is a bait delivery system which
allows accurate baiting of a very wide variety of baits. There
is no quicker way of delivering bait than a spod (besides a
bait boat which I'll talk about in a future article). If done
correctly, spodding can produce large bags of fish.
Rods and reels
When filled with bait a large spod can
weigh as much as 6 -7oz, far too much for the average carp rod
to cast, so a dedicated spod rod with a test curve of 4lb or
more is required. Most manufacturers now offer a bespoke spod
rod in their range.

I use a Greys Marker spod rod which is a 12'
rod with a 4lb test curve |

I use a Shimano GTX 8000 reel filled with
low diameter non stretch floating braid (Whiplash
Pro) in 30lb breaking strain. Even at 30lb breaking
strain the braid has the same diameter as 5lb
mono |
A large spooled reel is essential to take the strain out of
spodding. These big reels will make casting and retrieving the
spods a lot easier.
The spool of braid should always be wetted before you start
casting to minimize wind knots. The floating braid makes
gathering the line after the cast really easy and assists in
lifting the spod onto the plane during the retrieve of the
spod.

It is important to note that the spool must
not be filled to the lip of the spool as you would
with mono as you will suffer from wind knots during the
cast |
When using braid you must always use a leather finger stool
or a golfing or dedicated casting glove to protect you casting
finger from the braid.
Leaders
When casting a heavy bait-filled spod you
need a leader that will take the stress of the cast. Many
manufacturers make very good leader material in both mono and
braid. This leader not only protects against snapping the line
during the initial stages of casting but also helps to protect
your fingers against line cuts.

I have been using Korda Arma-Kord in 50lb
bs |

The leader is connected to the
mainline with a double grinner
knot |
Spods
A spod is like a large groundbait feeder
blocked off at one end, often as large as a coke can. Unlike a
groundbait feeder the spod has a buoyant nose cone which when
filled with bait and cast into the lake causes the spod to tip
and therefore self-empty.

A wide range of spods are available to suit
most baiting
needs |
Accuracy
When we know where we want to place our
bait and our marker float is sat in the required position in
our swim (see my article 'Feature finding with a marker float') it's
time to range the spod to the marker float. We do this by
replacing the spod with a heavy lead and casting at the marker
float until we land the lead next to the spod with our rod
held vertically, cushioning the cast.
With the lead still out in the lake, place the line in the
line clip and mark the line. It is now trapped behind the line
clip so it is essential to feather the casts with the spod by
holding the rod vertically. This prevents the spod from
stopping too abruptly and bouncing back towards you and
therefore potentially causing line-breaks and damage to the
line clip on the spool.

Set the range to spod to using a marker
float |

Tying a marker knot with pole
elastic |

Pole elastic marker knot in position and
slides freely through the eyes |

Knot lays neatly onto the spool and does
not impair the
cast |

Placing the line in the line clip ensures the
spod lands at the same range on every
cast |
Filling
Spods can be used to deliver a wide rand
and variety of baits. To get the best accuracy when we are
spodding it is critical we do not overfill the spod.

Overfilled spods do not fly straight and will
want to tumble during flight |

Cap the spod with a groundbait plug
to prevent spod-spill during
casting |
Loose baits like pellets, maggots and small boilies
(particles) will, if not trapped in place, fall out the back
of the spod during casting (known as spod-spill). To stop this
you can use a little plug of groundbait or a couple of large
PVA nuggets in the back of the spod.
Casting
Cast out your spod towards your marker
float, overhead style. During the cast it is important that
you cast with enough power to just get past the marker float.
After releasing the line on the cast pull the rod back to the
vertical position. As you feel the line tighten, quickly drop
the rod forward to the horizontal to allow you to cushion the
cast and ensure better accuracy and prevent line snapping and
breaking the line clip off the reel spool. When the spod hits
the water it should hit with a slap on a tight line, this
takes a lot of practice but ensures the minimum amount of
disturbance to the swim.

Cast out your spod towards your
marker-float overhead style |

Allow the spod time to settle and the
feed chance to escape the
spod |

Give the rod a couple of short sharp pulls to
agitate the spod and assist the feed to exit the
spod |

A nice tight bed of maggots and ground
bait right on top of your
marker |
When the spod is empty, lift your rod and reel fast and
smooth to retrieve the spod. Always try to get the spod to
come up onto the surface of the water as quickly as possible.
This will make it easier to retrieve and make the process less
tiring.
Have fun with your new spodding skills and remember -
you can always add bait to your swim but you can't remove
it.